Révisions pour end-gcode.gcode

Lucas Teske a révisé ce gist 4 years ago. Aller à la révision

2 files changed, 47 insertions

end-gcode.gcode(fichier créé)

		@@ -0,0 +1,13 @@
1	+	G91 ;Relative positioning
2	+	G1 E-2 F2700 ;Retract a bit
3	+	G1 E-2 Z0.2 F2400 ;Retract and raise Z
4	+	G1 X5 Y5 F3000 ;Wipe out
5	+	G1 Z10 ;Raise Z more
6	+	G90 ;Absolute positionning
7	+
8	+	G1 X0 Y{machine_depth} ;Present print
9	+	M106 S0 ;Turn-off fan
10	+	M104 S0 ;Turn-off hotend
11	+	M140 S0 ;Turn-off bed
12	+
13	+	M84 X Y E ;Disable all steppers but Z

start-gcode.gcode(fichier créé)

		@@ -0,0 +1,34 @@
1	+	; Script based on an original created by tjjfvi (https://github.com/tjjfvi)
2	+	; An up-to-date version of the tjjfvi's original script can be found
3	+	; here: https://csi.t6.fyi/
4	+	; Note - This script will only work in Cura V4.2 and above!
5	+	; --- Global Settings
6	+	; layer_height = {layer_height}
7	+	; smooth_spiralized_contours = {smooth_spiralized_contours}
8	+	; magic_mesh_surface_mode = {magic_mesh_surface_mode}
9	+	; machine_extruder_count = {machine_extruder_count}
10	+	; --- Single Extruder Settings
11	+	; speed_z_hop = {speed_z_hop}
12	+	; retraction_amount = {retraction_amount}
13	+	; retraction_hop = {retraction_hop}
14	+	; retraction_hop_enabled = {retraction_hop_enabled}
15	+	; retraction_enable = {retraction_enable}
16	+	; retraction_speed = {retraction_speed}
17	+	; retraction_retract_speed = {retraction_retract_speed}
18	+	; retraction_prime_speed = {retraction_prime_speed}
19	+	; speed_travel = {speed_travel}
20	+
21	+	; Ender 3 Custom Start G-code
22	+	G21 ; Set units to mm
23	+	G92 E0 ; Reset Extruder
24	+	G28 ; Home all axes
25	+	; G29 ; BL Touch
26	+	M420 S1 ; Load BL Touch
27	+	G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
28	+	G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position
29	+	G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line
30	+	G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little
31	+	G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line
32	+	G92 E0 ; Reset Extruder
33	+	G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
34	+	G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish

Plus récent Plus ancien